Product Family / Category. INCA. Product / Topic. INCA-MIP. Type. Manual / Technical Documentation. Title. INCA-MIP V User’s Guide. INCA V – Tutorial. ETAS. Lesson: Measuring. Create a recorder for manual recordings. You are in the Experiment Environment. To create a recorder . This INCA manual consists of the following chapters: • Chapter 1: ”Introduction” ( this chapter). This chapter outlines the possible INCA (INtegrated Calibration.
|Published (Last):||3 November 2010|
|PDF File Size:||1.39 Mb|
|ePub File Size:||1.9 Mb|
|Price:||Free* [*Free Regsitration Required]|
This may lead to a restriction of the value range and force a incrementation. Colors, transparency, lines, points, light source configurable.
Usually a label is implemented in a ECU using computer data types and then calculated to physical values using a conversion formula.
ETAS – INCA ASAM MCD-3MC V Interface – User’s Guide – Download Center – ETAS Products
The gradient between neighbor label values will be limited. Consideration of axes groups, units, increments. The third one is then interpolated from the active map. This feature enables to close visible eas invisible windows automatically. Activate this option if a even connection to the neighboring areas should be created for partial smoothing. The map size, distribution type, name and units can be defined.
ETAS – INCA ASAM MCD-3MC V2.2 Interface – User’s Guide – Download Center
Before you have to copy them directly to eta clipboard or as strings containing the file names line by line. It is also possible to add lines, arrows, text boxes etc. Above the map they are colored white and under the map gray. Create a plot with lines from to in steps of After termination of the smoothing the map points that were restricted to smooth by the corridor width or the error criterion will be marked to be able to judge the smoothing options chosen.
Then you mark the area to extrapolate and call the function again.
ETAS – INCA-MIP V7.0 User’s Guide – Download Center
Default is the name of the loaded template label. Especially all files must be located in the same directory. This feature enables to automatically arrange windows.
Additionally you have the option to close the source MapArtist windows after import. Choose the grade of transparency and the color in the corresponding menu. In this way, you determine the direction of the inversion.
The file will be asked and you can choose from all map labels in the file. Therefore a set of functionality is available to create and smooth the map and axes distribution. If you want the result to be a map showing the load over speed and torque, select “Y-axis” as the target axis.
All conditions are combined with OR. Select the the time to wait before activating the next window. The axis pane and value are shown during modification.
SGE MapArtist Manual
Create contour plot with 20 lines and automatic values. The decision can be remembered. This will be used in case the map is saved as DCM later to use the correct group axes, units and to define the conversion rule used while editing the map, e.
Choose the decimal separator for numbers to use when copying to clipboard. The axes optimization can be restricted to single directions and breakpoint ranges. The number depends on the following settings. In general you should prefer accuracy.
This option will only have an effect if data points are loaded. Therefore it is possible to optimize axes with focus on specific map regions.
Duplication, processing, eats or any form of commercialization of the documents content beyond the scope of the copyright law shall require the prior written consent of the SGE Ingenieur GmbH. Select the target monitor for the windows to arrange in case of multiple monitors are connected to the computer.
The working page of the active map will be interpolated to the axes of the template map to load.
This option is relevant for all points of the new axis that are above the map to be inverted. To adjust to the practical needs a gain factor can be set. Set axes ranges or set axes tick to accord with map breakpoints In the second case multiple data point sets will be created. Before sending the map to INCA it has to be verified that no function, which is relevant for secure operation, might be influenced.
Additionally column and row based layouts are available. If label points are marked, only the marked points are regarded.
You can either double click onto a data point or use the menu. Automatic or manual zoom and Pan. Leave the calculation empty if you don’t stas logical deletion.
The map is created by optimizing a Gaussian Process Model to fit the data’ points.